MP4-3W-2W-30-A - Astec MP4-3W-2W-30-A 400W Power Supply Simple Type: Power Supply
Request Quote
For Price
- Part Number:
- MP4-3W-2W-30-A
- Model Number:
- MP4-3W-2W-30-A
- Make:
- ASTEC
- Lead Time:
- Available
- Qty In Stock:
- Available
Astec MP4-3W-2W-30-A 400W Power Supply Simple Type: Power Supply
For Resellers and High Volume Orders:
Please request a quote to obtain preferred pricing.
Features
- 2 year warranty
- Additional 200 W output @ high line (180-264 VAC)
- CISPR 22, EN55022 Curve B conducted/radiated EMI
- Current share on all outputs with ratings of 10 A or greater
- Customer-provided air option
- EN61000 immunity standards
- EN61000-3-2 harmonic distortion compliance
- European CE Mark requirements
- Fan fail signal
- Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac & 25 °C ambient conditions
- Forced air cooling, field replaceable fan
- Global and individual module inhibits/enable
- Global DC OK signal and status indicator LED
- Input OK signal and status indicator LED
- Isolated 5 V bias voltage
- Low leakage option for medical applications
- Low noise fan
- Margining on all single output modules
- Module enable
- Optional VME timing and system DC OK module
- Outputs down to 0.5V
- Overload protection on all outputs
- Power factor correction
- Remote sense on all outputs with ratings greater than 2 A
- Standard modification flexibility (consult factory)
- Voltage adjustment on all outputs
Specifications
- AC OK: >5 ms early warning min. before outputs loose regulation; Full cycle ride thru (50 Hz)
- Adjustment range: ±10% min. all outputs
- Cooling: Internal DC fan (Field replaceable)
- DC OK: -2% to -8% of nominal for any monitored output
- Dynamic response: <2% or 100 mV, with 25% load step.
- Efficiency: 70-80% typ. @ full case load
- Frequency: 47-440 Hz
- Global Inhibit/Enable: TTL, Logic “1” and Logic “0”
- Harmonic distortion: Meets EN61000-3-2
- Holdover storage: 20 ms minimum (independent of input VAC)
- Housekeeping Bias voltage: 5 VDC @250 mA max. present whenever AC input is applied
- Humidity: 95% non-condensing
- Input fuse (internal): 10 A
- Input Voltage: 85-264 VAC; 120-350 VDC
- Inrush Current: 40 A peak max.
- Isolation: Meets EN60950
- Leakage current(low leakage option): 300 mA max. @ 240 VAC
- Margining: ±4-6% nom.1
- Minimum Load: Not required on single or triple output modules. 10% required on main of dual output modules3 (Consult factory if pre-loaded required)
- Module inhibit: TTL, isolated, singles and dual (both outputs) only
- Operating temperature: -20°C to 50°C (start @ 0°C)(derate each output linearly to 50% at 70°C)(-20°C to 40°C max. with rear air option)
- Output/Output isolation: >1 Megohm
- Overall reg: 0.4% or 20 mV max. (36 W modules 4% max.)
- Overcurrent protection: Single, main of dual output module 105-120% of rated output current. Aux output of dual output module 105-140% of rated output current. Triple output module Internally protected
- Overvoltage Protection: Single output modules (measured at sense 2-5.5 V 122-134% connection) 6-60 V 110-120%
- Power Factor: 0.99 typ. meets EN61000-3-2
- Radiated EMI: CISPR 22; EN55022 Level “B”
- Recovery time: To within 1% in <300 µsec.
- Remote sense: Up to 0.5 V total drop
- Reverse voltage protection: 100% of rated output current
- Ripple: RMS: 0.1% or 10 mV, whichever is greater; Pk-Pk: 1.0% or 50 mV, whichever is greater; Bandwidth limited to 20 MHz
- Shock/Vibration: Mil-Hdbk 810E
- Short Circuit Protection: Protected for continuous short circuit. Recovery is automatic upon removal of short
- Single wire parallel: Current share to within 2% of total rated current
- Storage temperature: -40°C to +85°C
- Switching frequency: 250 kHz
- Temperature coefficient: 0.02% per °C
- Thermal protection: All outputs disabled when internal temp exceeds safe operating range. >5 ms warning (AC OK signal) before shutdown
- Turn-on time: AC on 1.5 sec typ., Inhibit/Enable 150 ms typ.
Applications
- None Available
Aliases
- None Available